Workplace safety · United States

What Should a Lockout/Tagout Procedure Include?

A compliant lockout/tagout procedure should identify the machine and hazardous energy, set the shutdown and isolation sequence, require verification, define who may apply and remove devices, and cover restoration, training and periodic inspection.

A stop button is not an energy-isolation device. Before cleaning, unjamming, adjusting or maintaining equipment, operators need a procedure that identifies every hazardous energy source, isolates it, controls stored energy and proves the equipment cannot restart unexpectedly.

The short answer

Under federal OSHA's lockout/tagout standard, an energy-control procedure should state its purpose and scope; identify the machine, energy sources and responsible roles; give specific steps for shutdown, isolation, locking or tagging, stored-energy control and verification; and explain how devices are removed and equipment is safely returned to service. The wider program must also cover employee training and periodic inspections. State-plan rules may be different or more stringent, so confirm the rule that applies at each location.

When does lockout/tagout apply?

Federal OSHA standard 29 CFR 1910.147 covers servicing and maintenance where unexpected energization or startup, or the release of stored energy, could injure an employee. Covered work can include installing, setting up, adjusting, inspecting, cleaning, unjamming, lubricating, modifying and maintaining equipment when that exposure exists.

For retail, hospitality, food-to-go and other frontline operations, the question can arise around balers, compactors, conveyors, bakery mixers, slicers, commercial dish machines, powered doors, and refrigeration or HVAC equipment. The label on the task does not decide coverage. A two-minute jam clearance may be servicing if a worker enters a danger zone and unexpected movement could cause injury.

Normal production operations are generally outside the standard, but the rule applies to servicing during production when a worker must remove or bypass a guard or place any part of the body into a point of operation or associated danger zone. The minor-servicing exception is narrow: the activity must take place during normal production, be routine, repetitive and integral to production, and use alternative measures that provide effective protection. Do not treat “quick task” as an exception.

Cord-and-plug equipment has a separate exception when it is unplugged and the plug remains under the exclusive control of the employee doing the servicing. Construction, agriculture, maritime work and certain electrical work are governed by other OSHA provisions. Check the applicable standard rather than applying a general-industry checklist outside its scope.

Why review this now?

On 16 November 2026, OSHA announced citations against a New Jersey pastry manufacturer and a staffing agency after two workers were injured while cleaning the same conveyor. OSHA alleged failures including the development and use of lockout/tagout procedures and adequate training, and proposed penalties totaling $351,120. The employers may contest the citations, so the announcement is an enforcement allegation and proposed penalty, not a final adjudication.

What should the written procedure contain?

29 CFR 1910.147(c)(4) requires covered energy-control procedures to be developed, documented and used, subject to a limited exception for certain simple single-energy-source equipment. A generic policy is not enough when an authorized employee needs machine-specific information to isolate equipment safely.

A practical procedure should include:

  • Identity and scope: the machine or equipment, location, procedure owner, intended use and the servicing tasks covered.
  • Energy inventory: each electrical, mechanical, hydraulic, pneumatic, chemical, thermal, gravitational or other energy source, including stored or residual energy.
  • Isolation points: the type and location of disconnects, valves, blocks, blanks or other energy-isolating devices. Control-circuit devices such as push buttons and selector switches are not energy-isolating devices.
  • Authorisation: who may apply locks or tags, who is affected by the shutdown, and how compliance with the procedure is enforced.
  • Shutdown and isolation steps: the specific order for stopping the equipment, operating every required energy-isolating device and applying personal lockout or tagout devices.
  • Stored-energy controls: how pressure is bled, elevated parts are blocked, springs are restrained, capacitors are discharged, hot surfaces cool or other residual energy is rendered safe.
  • Verification: the test or try step used to confirm isolation before work begins, including the controls that must be returned to neutral or off after the test.
  • Device control: rules for placement, identification, transfer and removal of locks and tags, including the employer's documented process if the employee who applied a device is unavailable.
  • Return to service: inspection of the work area, removal of tools and employees, confirmation that controls are neutral, authorised device removal, re-energization and notification of affected employees.
  • Non-routine arrangements: contractor work, group lockout, shift changes and any testing or positioning that requires temporary re-energization.

OSHA's Appendix A provides a typical minimal procedure, but it is a non-mandatory aid rather than a substitute for assessing the actual machine. Complex systems, multiple energy sources and shared isolation arrangements need more detail.

What sequence should workers follow?

The procedure must be usable at the equipment, not merely accurate on paper. Federal OSHA sets out this core application sequence:

  1. Prepare. The authorized employee identifies the type and magnitude of energy, its hazards and the means of control.
  2. Notify. Affected employees are told that the machine will be shut down and locked or tagged out.
  3. Shut down. The equipment is stopped using its normal stopping procedure in a way that avoids creating an additional hazard.
  4. Isolate. Every energy-isolating device needed to control the equipment is physically located and operated.
  5. Apply devices. Authorized employees affix lockout or tagout devices to each isolating device. Where the isolating device can be locked out, lockout is required unless the employer demonstrates equivalent full employee protection from a tagout system.
  6. Control stored energy. Residual or stored energy is relieved, disconnected, restrained or otherwise made safe. If it can reaccumulate, isolation continues to be verified.
  7. Verify isolation. Before work starts, the authorized employee verifies that isolation and de-energization have been accomplished.
  8. Release safely. Before devices are removed, the authorized employee checks the machine and work area, ensures employees are safely positioned, removes devices under the rule's requirements and notifies affected employees before startup.

Do not collapse verification into “the power light is off.” The method should match the hazard: try the operating control, test for voltage with suitable equipment, check a pressure gauge, prove a block is carrying the load or use another reliable test specified by a competent person.

Which roles and training must be defined?

The standard distinguishes roles because each person needs different knowledge:

  • Authorized employees apply lockout or tagout to perform servicing. They need training to recognize hazardous energy sources, understand the type and magnitude of energy present, and know the methods needed for isolation and control.
  • Affected employees operate or use the equipment, or work in the area where servicing occurs. They need instruction on the purpose and use of the energy-control procedure and must not restart or re-energize locked or tagged equipment.
  • Other employees whose work may bring them into the area need instruction about the procedure and the prohibition on restarting or interfering with locked or tagged equipment.

Retraining is required when an employee's job assignment changes, equipment or processes create a new hazard, the energy-control procedure changes, or an inspection or other evidence shows deviations or inadequate knowledge. Training records should identify the employee and training date. Attendance alone does not establish that an authorized employee can isolate the actual equipment, so add a practical competence check where appropriate.

How should special situations be handled?

Contractors and staffing-agency workers

When outside servicing personnel perform covered work, the on-site employer and outside employer must inform each other of their lockout or tagout procedures. The on-site employer must ensure its employees understand and comply with the restrictions and prohibitions of the outside employer's program. The November 2026 OSHA release is also a reminder that host and staffing employers need clear, verified training arrangements for temporary workers.

Group lockout/tagout

Group arrangements must give each authorized employee protection equivalent to a personal lock or tag. A single authorized employee has primary responsibility for the group, and each authorized employee applies a personal device when work begins and removes it when work ends. Where several crews or departments are involved, designate coordination responsibility explicitly.

Shift or personnel changes

The procedure must provide for an orderly transfer of protection between outgoing and incoming employees. Avoid an informal handover that leaves equipment isolated under a departed worker's lock or creates a gap while the next shift takes control.

Testing or positioning

If power must be restored temporarily to test or position equipment, the rule provides a sequence: clear tools and materials, remove employees from the area, remove devices as required, energize for the test, then de-energize and reapply energy-control measures before servicing continues. This is a controlled exception within the procedure, not permission to troubleshoot exposed equipment under normal power.

What should the annual inspection record show?

The employer must inspect each energy-control procedure at least annually to confirm that it is being followed and remains adequate. The inspector must be an authorized employee other than the employees using the procedure being inspected. Identified deviations and inadequacies must be corrected.

The certification should identify:

  • the machine or equipment on which the procedure was used;
  • the inspection date;
  • the employees included in the inspection; and
  • the person who performed the inspection.

For lockout, the inspection includes a review of each authorized employee's responsibilities under the procedure. For tagout, it also includes affected employees' responsibilities and the additional tagout training requirements. An annual diary reminder is useful, but the inspection should observe the procedure in use and lead to corrective action when practice and paperwork diverge.

How should multi-site operators manage LOTO?

A corporate policy can set minimum rules, but equipment-specific control must remain accurate locally. Multi-site operators should maintain a controlled register showing, for each relevant asset:

  • site, asset identifier and current procedure version;
  • energy sources and isolation points;
  • authorized roles and current competence status;
  • lockout-device availability and storage location;
  • last periodic inspection, inspector and next due date;
  • open defects, temporary restrictions and corrective actions;
  • contractor ownership and coordination arrangements; and
  • changes to equipment, process or staffing that trigger review.

Standardize the governance fields, approval rules and inspection evidence, but do not copy one machine's isolation diagram onto another. Site teams should verify procedures after installation, relocation, modification or major repair and whenever an incident, near miss or worker concern suggests that the listed isolation points are incomplete.

Common gaps to look for

  • A single generic procedure that does not identify the equipment, energy sources or isolation points.
  • Reliance on an emergency-stop button, interlock or software control instead of an energy-isolating device.
  • No method for blocking gravity, relieving pressure or checking reaccumulating energy.
  • A shutdown sequence with no independent verification step.
  • Managers removing another employee's lock without a documented exceptional-removal process.
  • Contractors using a different system without an exchange of procedures and site coordination.
  • Temporary or night-shift employees operating near servicing work without affected-employee instruction.
  • Annual reviews completed as paperwork exercises without observing the procedure or correcting deficiencies.
Connect procedures to site evidence

Fit2Trade Ensure can help multi-site teams connect equipment risks, training, inspections and corrective actions to accountable owners. The lockout/tagout procedure, equipment-specific isolation method and competent authorization still need to be set and verified by the employer for each workplace.

Explore Fit2Trade Ensure

Primary sources

Keep exploring

More practical guidance.

Browse Insights